az10e131 az100e131 ecl/pecl 4-bit d flip-flop 1630 s. stapley dr., suite 125 ? mesa, arizona 85204 ? usa ? (480) 962-5881 ? fax (480) 890-2541 www.azmicrotek.com arizona microtek, inc. features ? 1100 mhz min. toggle frequency ? differential outputs ? individual and common clocks ? individual resets (asynchronous) ? paired sets (asynchronous) ? operating range of 4.2v to 5.46v ? 75k ? internal input pulldown resistors ? direct replacement for on semiconductor mc10e131 & mc100e131 description the az10/100e131 is a quad master-slave d-type flip-flop with differential outputs. each flip-flop may be clocked separately by holding common clock (c c ) low and using the clock enable (ce n) inputs for clocking. common clocking is achieved by holding the ce n inputs low and using c c to clock all four flip-flops. in this case, the ce n inputs perform the function of contro lling the common clock to each flip-flop. individual asynchronous resets are provided (rn). asynchronous set controls (sn) are ganged together in pairs, with the pairing chosen to reflect physical chip symmetry. data enters the master when both c c and ce n are low, and transfers to the slave when either c c or ce n (or both) go high. note: specifications in ecl/pecl tables are valid when thermal equilibrium is established. package availability package part no. marking plcc 28 az10e131fn azm10e131 plcc 28 t&r az10e131fnr2 azm10e131 plcc 28 AZ100E131FN azm100e131 plcc 28 t&r AZ100E131FNr2 azm100e131 26 27 28 1 2 3 4 v cco v cc nc v cco v ee 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 r3 d2 ce2 r2 q3 q3 q2 q2 q1 q1 q0 q0 r1 ce1 d1 r0 ce0 d0 s03 c c s12 d3 ce3 * all v cc and v cco pins are tied together on the die. pinout: 28-lead plcc (top view)
az10e131 az100e131 october 2001 * rev - 2 www.azmicrotek.com 2 absolute maximum ratings are those values beyond which device life may be impaired. symbol characteristic rating unit v cc pecl power supply (v ee = 0v) 0 to +8.0 vdc v i pecl input voltage (v ee = 0v) 0 to +6.0 vdc v ee ecl power supply (v cc = 0v) -8.0 to 0 vdc v i ecl input voltage (v cc = 0v) -6.0 to 0 vdc i out output current --- continuous --- surge 50 100 ma t a operating temperature range -40 to +85 c t stg storage temperature range -65 to +150 c 10k ecl dc characteristics (v ee = -4.94v to -5.46v, v cc = v cco = gnd) -40 c 0 c 25 c 85 c symbol characteristic min typ max min typ max min typ max min typ max unit v oh output high voltage 1 -1080 -890 -1020 -840 -980 -810 -910 -720 mv v ol output low voltage 1 -1950 -1650 -1950 -1630 -1950 -1630 -1950 -1595 mv v ih input high voltage -1230 -890 -1170 -840 -1130 -810 -1060 -720 mv v il input low voltage -1950 -1500 -1950 -1480 -1950 -1480 -1950 -1445 mv i ih input high current c c s r, ce d 350 450 300 150 350 450 300 150 350 450 300 150 350 450 300 150 a i il input low current 0.5 0.5 0.5 0.5 a i ee power supply current 58 70 58 70 58 70 58 70 ma 1. each output is terminated through a 50 ? resistor to v cc ? 2v. logic symbol s d r s d r r d s r d s d3 d2 r2 r1 ce1 r0 ce0 d0 q2 q0 q0 q1 q1 q2 q3 q3 ce3 r3 ce2 s03 s12 c c d1 pin description pin function d0 ? d3 data inputs ce0 ? ce3 clock enables (individual) r0 ? r3 resets c c common clock s03,s12 sets (paired) q0 ? q3 true outputs q0 ? q3 inverting outputs v cc , v cco positive supply v ee negative supply nc no connect
az10e131 az100e131 october 2001 * rev - 2 www.azmicrotek.com 3 10k pecl dc characteristics (v ee = gnd, v cc = v cco = +5.0v) -40 c 0 c 25 c 85 c symbol characteristic min t yp max min t yp max min t yp max min t yp max unit v oh output high voltage 1,2 3920 4110 3980 4160 4020 4190 4090 4280 mv v ol output low voltage 1,2 3050 3350 3050 3370 3050 3370 3050 3405 mv v ih input high voltage 1 3770 4110 3830 4160 3870 4190 3940 4280 mv v il input low voltage 1 3050 3500 3050 3520 3050 3520 3050 3555 mv i ih input high current c c s r, ce d 350 450 300 150 350 450 300 150 350 450 300 150 350 450 300 150 a i il input low current 0.5 0.5 0.5 0.5 a i ee power supply current 58 70 58 70 58 70 58 70 ma 1. for supply voltages other that 5.0v, use th e ecl table values and add supply voltage value. 2. each output is terminated through a 50 ? resistor to v cc ? 2v. 100k ecl dc characteristics (v ee = -4.2v to -5.46v, v cc = v cco = gnd) -40 c 0 c 25 c 85 c symbol characteristic min typ max min typ max min typ max min typ max unit v oh output high voltage 1 -1085 -1005 -880 -1025 -955 -880 -1025 -955 -880 -1025 -955 -880 mv v ol output low voltage 1 -1830 -1695 -1555 -1810 -1705 -1620 -1810 -1705 -1620 -1810 -1705 -1620 mv v ih input high voltage -1165 -880 -1165 -880 -1165 -880 -1165 -880 mv v il input low voltage -1810 -1475 -1810 -1475 -1810 -1475 -1810 -1475 mv i ih input high current c c s r, ce d 350 450 300 150 350 450 300 150 350 450 300 150 350 450 300 150 a i il input low current 0.5 0.5 0.5 0.5 a i ee power supply current 58 70 58 70 58 70 67 81 ma 1. each output is terminated through a 50 ? resistor to v cc ? 2v. 100k pecl dc characteristics (v ee = gnd, v cc = v cco = +5.0v) -40 c 0 c 25 c 85 c symbol characteristic min t yp max min t yp max min t yp max min t yp max unit v oh output high voltage 1,2 3915 3995 4120 3975 4045 4120 3975 4045 4120 3975 4045 4120 mv v ol output low voltage 1,2 3170 3305 3445 3190 3295 3380 3190 3295 3380 3190 3295 3380 mv v ih input high voltage 1 3835 4120 3835 4120 3835 4120 3835 4120 mv v il input low voltage 1 3190 3525 3190 3525 3190 3525 3190 3525 mv i ih input high current c c s r, ce d 350 450 300 150 350 450 300 150 350 450 300 150 350 450 300 150 a i il input low current 0.5 0.5 0.5 0.5 a i ee power supply current 58 70 58 70 58 70 67 81 ma 1. for supply voltages other that 5.0v, use the ecl table values and add supply voltage value. 2. each output is terminated through a 50 ? resistor to v cc ? 2v.
az10e131 az100e131 october 2001 * rev - 2 www.azmicrotek.com 4 ac characteristics (v ee = 10e(-4.94v to -5.46v), 100e(-4.2v to -5.46v); v cc = v cco = gnd or v ee = gnd, v cc =v cco = 10e(+4.94v to +5.46v), 100e(+4.2v to +5.46v)) -40 c 0 c 25 c 85 c symbol characteristic min typ max min typ max min typ max min typ max unit f max max. toggle frequency 1100 1400 1100 1400 1100 1400 1100 1400 mhz t plh / t phl propagation delay to output ce c c r s 310 275 300 300 600 600 620 550 750 725 775 775 360 325 350 350 500 500 550 550 700 675 725 725 360 325 350 350 500 500 550 550 700 675 725 725 360 325 350 350 500 500 550 550 700 675 725 725 ps t s setup time 2 d 200 20 150 20 150 20 150 20 ps t h hold time 2 d 225 -20 175 -20 175 -20 175 -20 ps t rr reset recovery time 450 150 400 150 400 150 400 150 ps t pw minimum pulse width clk, s, r 400 400 400 400 ps t skew within-device skew 1 60 60 60 60 ps t r / t f rise/fall times 20% - 80% 275 725 300 675 300 675 300 675 ps 1. within-device skew is defined as identi cal transitions on similar paths through a device. 2. setup/hold times guaranteed for both c c & ce .
az10e131 az100e131 october 2001 * rev - 2 www.azmicrotek.com 5 package diagram plcc 28 n otes: 1. datums ?l-, -m-, and ?n- determined where top of lead shoulder exits plastic body at mold parting line. 2. dimension g1, true position to be measured at datum ?t-, seating plane. 3. dimensions r and u do not include mold flash. alowable mold flash is 0.010mm (0.250in.) per side. 4. dimensioning and tolerancing per ansi y14.5m, 1982. 5. controlling dimension: inch. 6. the package top may be smaller than the packge bottom by up to 0.012mm (0.300in.). dimensions r and u are determined at the outermost extremes of the plastic body exclusive of mold flash, the bar burrs, gate burrs and interlead flash, but including any mismatch between the top and bottom of the plastic body. 7. dimension h does not include dambar protrusion or intrusion. the dambar protrusion(s) shall not cause the h dimension to be smaller than 0.025mm (0.635in.). millimeters inches dim min max min max a 12.32 12.57 0.485 0.495 b 12.32 12.57 0.485 0.495 c 4.20 4.57 0.165 0.180 e 2.29 2.79 0.090 0.110 f 0.33 0.48 0.013 0.019 g 1.27 bsc 0.050 bsc h 0.66 0.81 0.026 0.032 j 0.51 0.020 k 0.64 0.025 r 11.43 11.58 0.450 0.456 u 11.43 11.58 0.450 0.456 v 1.07 1.21 0.042 0.048 w 1.07 1.21 0.042 0.048 x 1.07 1.42 0.042 0.056 t 0.50 0.020 z 2 o 10 o 2 o 10 o g1 10.42 10.92 0.410 0.430 k1 1.02 0.040
az10e131 az100e131 october 2001 * rev - 2 www.azmicrotek.com 6 arizona microtek, inc. reserves the right to change circuitry a nd specifications at any time without prior notice. arizona mic rotek, inc. makes no warranty, representation or guarant ee regarding the suitability of its products for any particular purpose, nor does a rizona microtek, inc. assume any liability arising out of the applica tion or use of any product or ci rcuit and specifically disclaims any and all liability, including without limitation special, consequential or inci dental damages. arizona microtek, inc. does not convey a ny license rights nor the rights of others. arizona microtek, inc. products are not designed, intended or authorized for use as component s in systems intended to support or sustain life, or for any other applicati on in which the failure of the arizona microtek, inc. product co uld create a situation where personal injury or death may occur. should bu yer purchase or use arizona microtek, inc. products for any such unintended or unauthorized application, buyer shall indemnify a nd hold arizona microtek, inc. a nd its officers, employees, subs idiaries, affiliates, and distributor s harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising ou t of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthori zed use, even if such claim al leges tha t arizona microtek, inc. was negligent regarding the design or manufacture of the part.
|
